|
 |
Author |
|
Message |  |
|
jema Downsizer Moderator
Joined: 28 Oct 2004 Posts: 26626 Location: escaped from Swindon
|
|
|
|
 |
dpack
Joined: 02 Jul 2005 Posts: 34729 Location: yes
|
Posted: Mon Apr 18, 16 5:02 pm Post subject: |
|
go for the thicker walls
both will need a proper felting job with mastic to stay dry for more than a year or so
both will require extra ventilation(drill holes under the eaves and secure with flyscreen mesh)
both will require extra trusses to be able to use the overhead space for storage of long things.
both will need wood treatment or paint every few years.
if you have a boy dog an exterior ply "target" strip around the lower part of the walls helps to prevent "erosion"
both will require a decent base(min 300 mm well bumped hardcore topped with flags or concrete) to prevent wonkyness which causes doors to stick corners to open etc etc .
both will need rat proofing underneath
both will require extra timbers for fitting shelves etc ( even the thicker walls are too thin to hold anything but cuphooks for light things.
do the electrics properly bearing in mind tumble dryers need quite a few amps as do power tools ,kettle or hotplate for brewing works etc(armoured cable is the easiest option and will mate up to a waterproof plug unit,wall glands ,rcd unit etc etc ) |
|
|
|
 |
dpack
Joined: 02 Jul 2005 Posts: 34729 Location: yes
|
Posted: Mon Apr 18, 16 5:13 pm Post subject: |
|
the used shipping container is a very adaptable bit of kit and although has a few difficulties it does avoid most of the ones i mention above. |
|
|
|
 |
jema Downsizer Moderator
Joined: 28 Oct 2004 Posts: 26626 Location: escaped from Swindon
|
Posted: Mon Apr 18, 16 5:28 pm Post subject: |
|
Well I was thinking free standing racking, as you say those walls either size are not made for hanging things on.
It is going on decking rather than the ground, so I think the floor will be reasonably protected.
The ceiling space won't be used for storage, the aim is for a nice clean work area.
Electrics will be as you say, I have a spare slot in the main fuse box lined up for this. |
|
|
|
 |
jema Downsizer Moderator
Joined: 28 Oct 2004 Posts: 26626 Location: escaped from Swindon
|
|
|
|
 |
dpack
Joined: 02 Jul 2005 Posts: 34729 Location: yes
|
Posted: Mon Apr 18, 16 6:10 pm Post subject: |
|
good there is a spare slot re electrics.
free standing racks are ok and will only need a plank under the feet to spread the load.
so long as the decking is stable and flat i would think it should be a reasonable base for a shed if the deck planks are at 90 degrees to the shed floor joists.if it is very wonky when you put a level and strait edge to it to check using 3 sheets of roofing board might be handy to give a flat level base, using the shims under the boards rather than direct under the joists which makes the thing stand on tip toe instead of flat footed.
ps they are fairly easy to put together and judging by the state of our one a diy job is likely to be better than an installer stapling the felt on for instance
pps adding plenty of mastic and a layer of heavy duty felt to a new shed will avoid having to do major roof repairs in a few years,run the extra felt over the soffits as water getting behind them is a main cause of rot in the roof timbers.(as is damp see note on extra ventilation) |
|
|
|
 |
Behemoth
Joined: 01 Dec 2004 Posts: 19023 Location: Leeds
|
Posted: Mon Apr 18, 16 7:32 pm Post subject: |
|
Self build?
Ship lap is about £13m2 and treated battens about £1 a metre. Or buy the stuff and pay s chippy to do it for you? |
|
|
|
 |
onemanband
Joined: 26 Dec 2010 Posts: 1473 Location: NCA90
|
Posted: Mon Apr 18, 16 7:50 pm Post subject: |
|
Beware internet sheds - I've known them delivered needing FULL assembly.
Try your local independent fencing/shed supplier............
10 x 7 Apex, Standard framing (IIRC 50x32(and at 450centres)) £550
10 x 8 Apex, Heavy framing (IIRC 90 x 48 (450 centres)) £760 .....
......Construction is a bit more crude, but are well solid sheds.
Comes as 7 panels - bangs together in minutes - Finishing touches aren't as good, but nothing hard to sort. 12mm T+G roof and floor |
|
|
|
 |
Mistress Rose
Joined: 21 Jul 2011 Posts: 10309
|
Posted: Tue Apr 19, 16 6:28 am Post subject: |
|
We have a couple of those metal flatpack containers and they are very good. Main problem with them is condensation, so you would have to be very careful about insulation. We mainly use them for storage, but also as a small workshop.
We are also looking at these. They seem very solid and there might be something within your budget. http://www.skinnerssheds.co.uk/ |
|
|
|
 |
vegplot
Joined: 19 Apr 2007 Posts: 21298 Location: Ynys Môn
|
|
|
|
 |
john of wessex
Joined: 18 Jun 2007 Posts: 2130
|
|
|
|
 |
derbyshiredowser
Joined: 11 Feb 2007 Posts: 806 Location: derbyshire
|
Posted: Sun Apr 02, 17 1:30 pm Post subject: |
|
I've had a 13x7 tantalised pent from these people
http://www.beastsheds.co.uk/contact
Very well made free delivery and erection and a 10 year guarantee. Very nice people to deal with I sent photo and measurements and they made it to go through my car port. |
|
|
|
 |
|